Práctica Ruteo Estático

   [pic 1][pic 2][pic 3][pic 4][pic 5]

[pic 6]

[pic 7]

[pic 8][pic 9]

IPV4

Topología

[pic 10]

Configuración R1

Router>enable

Router#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#hostname R1

R1(config)#line console 0

R1(config-line)#password cisco

R1(config-line)#login

R1(config-line)#exit

R1(config)#enable password jafet

R1(config)#service password-encryption

R1(config)#banner motd #Solo personal autorizado#

R1(config)#exit

R1#

%SYS-5-CONFIG_I: Configured from console by console

R1#write

Building configuration...

[OK]

R1#exit

Solo personal autorizado

User Access Verification Password:  

R1>enable Password:  

R1#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

R1(config)#interface serial 0/0

R1(config-if)#ip address 192.168.1.5 255.255.255.252

R1(config-if)#clock rate 64000

R1(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0, changed state to down

R1(config-if)#interface fastethernet 0/0

R1(config-if)#ip address 192.168.1.33 255.255.255.224

R1(config-if)#no shutdown

R1(config-if)#

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

 R1#

%SYS-5-CONFIG_I: Configured from console by console

R1#write

Building configuration...

[OK]

R1#

%LINK-5-CHANGED: Interface Serial0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up

Configuración R2

Router>enable

Router#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#hostname R2

R2(config)#line console 0

R2(config-line)#password cisco

R2(config-line)#login

R2(config-line)#exit

R2(config)#enable password jafet

R2(config)#service password-encryption

R2(config)#banner motd #Solo personal autotizado#

R2(config)#exit

R2#

%SYS-5-CONFIG_I: Configured from console by console

R2#write

Building configuration...

[OK]

R2#exit

Solo personal autotizado User Access Verification Password:  

R2>enable Password:  

R2#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

R2(config)#interface serial 0/0

R2(config-if)#ip address 192.168.1.9 255.255.255.252

R2(config-if)#clock rate 64000

R2(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial0/0, changed state to down

R2(config-if)#interface serial 0/1

R2(config-if)#ip address 192.168.1.6 255.255.255.252

R2(config-if)#no shutdown

R2(config-if)#

%LINK-5-CHANGED: Interface Serial0/1, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/1, changed state to up  

R2(config-if)#^Z

R2#

%SYS-5-CONFIG_I: Configured from console by console

R2#write

Building configuration...

[OK]

R2#

%LINK-5-CHANGED: Interface Serial0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up

Configuración R3

Router>enable

Router#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#hostname R3

R3(config)#line console 0

R3(config-line)#password cisco

R3(config-line)#login

R3(config-line)#exit

R3(config)#enable password jafet

R3(config)#service password-encryption

R3(config)#banner motd #Solo personal autorizado#

R3(config)#exit

R3#

%SYS-5-CONFIG_I: Configured from console by console

R3#write

Building configuration...

[OK]

R3#exit

Solo personal autorizado User Access Verification Password:  

R3>enable Password:  

R3#configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

R3(config)#interface serial 0/1

R3(config-if)#ip address 192.168.1.10 255.255.255.252

R3(config-if)#no shutdown

R3(config-if)#

%LINK-5-CHANGED: Interface Serial0/1, changed state to up

...